SSC JE Mechanical Syllabus 2018
Here we are discussing the detailed about SSC JE Mechanical Syllabus 2018 Exam of Paper 1 and Paper 2 as Topic & Sub-Topic wise. As you know the Staff Selection Commission has notified the recruitment of the Post of Junior Engineer in various Departments. All the Eligible applicants had already applied for the examination. Now the huge no of application form received for the post of JEN. So competition is going to nail biting situation like. So it is very important to prepare in a planned manners to get through this tough exam. The commission is published the final SSC JE Syllabus Mechanical Engineering 2018 Topic Wise here.
SSC JE 2018 Expected Exam Date:- March 2019
SSC JE Syllabus 2018 Mechanical Engineering
The SSC JE Exam 2018 is going to held in Three stages as Paper 1, Paper 2 and Document Verification. So each and every candidates who got selected finally will go under these phases. So now the commission has also revealed the Expected SSC JE 2018 Exam Date Tier 1 as notified above. So it is very less time left to prepare. Here we are help to providing the details SSC JE Syllabus 2108 Mechanical Engineering course. The Exam Syllabus is provide to understand the exam questions for candidates. So aspirants make your own exam preparation strategy to keep in mind the Exam Pattern and SSC JE Mechanical Syllabus 2018 as given below.
SSC JE Syllabus 2018 Mechanical PDF
Each and Every aspirants who are going to appear in the SSC Junior Engineer Exam 2018 is need to aware about the SSC JE Mechanical Syllabus 2018 PDF and their respective engineering courses. Here we are discussing the detailed Tier 1 and Tier Exam Pattern and Syllabus as below. The Examination is going to held in the following manners as:
Paper-I:– Objective Type (Computer Base Mode)
Paper-II:– Conventional Type (Written Exam)
Commission is now is released the detailed SSC JE Mechanical Syllabus 2018 Topic wise to for the participating students to know the exam question papers. The Detailed tentative Exam Scheme for Each Paper 1 & 2 is followed below:
SSC JE Exam Pattern Tier 1
|Paper||Subject||No Of Questions||Max Marks||Time|
|Paper-I (Objective Type) Computer Based Online||(i) General Intelligence and Reasoning||50||50||2 Hours|
Civil & Structural Engineering
SSC JE Exam Pattern Tier 2
|Paper-II (Descriptive Type)||Part-A (General Engineering)
Civil & Structural
Part-B (General Engineering) Electrical
Part-C (General Engineering)
- Paper 1 is consist of all question as Multiple Choice based and there is negative marking of 0.25 marks for each wrong answer.
- Candidates is mandatory to attempt their respective General Engineering Part subject as opted in application form only.
- If any candidate is not attempt their General Engineering Subject Part in Paper-I then his/her answer sheet of Paper-II will not be evaluated at any conditions.
SSC JE Exam Syllabus 2018
The Staff Selection Commission is decided to hold the competitive exam for recruiting the Civil, Electrical Mechanical Junior Engineer posts. The SSC JE 2018 Notification Exam will be held Objective Paper as Preliminary and Descriptive Paper as Mains exam. The Exam Paper is set according to the SSC JE Mechanical Syllabus 2018 published here. So candidates should have very well aware for the exam syllabus for preparation.
Importance of Syllabus
- Candidates is must be aware about the detailed SSC JE Mechanical Syllabus 2018 PDF and vica versa of their other subjects.
- The Exam Pattern and Syllabus s helps to understand the basic perception about the Examination.
- After going through the whole syllabus candidates must be focus on the most important topics of the subjects to get better score.
- It is also helps to make the SSC JE Exam Preparation Plan so that you can easily crack the examination.
- Candidates must be focused on the more weightage topics rather than less weightage topics.
- The SSC JE Exam pattern 2018 is help to making in the Time management of the Exam Papers.
SSC JE Mechanical Syllabus Paper 1 & 2
We are here discussing detailed indicative SSC JE Mechanical Syllabus 2018 PDF as Topic Wise and Subtopic wise as divided below.
Paper-I: (Objective Type)
Part C: (Mechanical Engineering)
Theory of Machines and Machine Design, Engineering Mechanics and Strength of Materials, Properties of Pure Substances, 1st Law of Thermodynamics, 2nd Law of Thermodynamics, Air standard Cycles for IC Engines, IC Engine Performance, IC Engines Combustion, IC Engine Cooling & Lubrication, Rankine cycle of System, Boilers, Classification, Specification, Fitting & Accessories, Air Compressors & their cycles, Refrigeration cycles, Principle of Refrigeration Plant, Nozzles & Steam Turbines.
Properties & Classification of Fluids, Fluid Statics, Measurement of Fluid Pressure, Fluid kinematics, Dynamics of Ideal fluids, Measurement of Flow rate, basic principles, Hydraulic Turbines, Centrifugal Pumps, Classification of steels.
Paper-II: (Conventional Type)
Part C:- (Mechanical Engineering)
|Theory of Machines and Machine Design||Concept of simple machine, Four bar linkage and link motion, Flywheels and fluctuation of energy, Power transmission by belts– V-belts and Flat belts, Clutches – Plate and Conical clutch, Gears– Type of gears, gear profile and gear ratio calculation, Governors – Principles and classification, Riveted joint, Cams, Bearings, Friction in collars and pivots.|
|Engineering Mechanics and Strength of Materials||Equilibrium of Forces, Law of motion, Friction, Concepts of stress and strain, Elastic limit and elastic constants, Bending moments and shear force diagram, Stress in composite bars, Torsion of circular shafts, Bucking of columns – Euler’s and Rankin’s theories, Thin walled pressure vessels.|
|Properties of Pure Substances||P-V & P-T diagrams of pure substance like H2O, Introduction of steam table with respect to steam generation process, definition of saturation, wet & superheated status. Definition of dryness fraction of steam, degree of superheat of steam. H-s chart of steam (Mollier‟s Chart).|
|1st Law of Thermodynamics||Definition of stored energy & internal energy, 1st Law of Thermodynamics of cyclic process, Non Flow Energy Equation, Flow Energy & Definition of Enthalpy, Conditions for Steady State Steady Flow, Steady State Steady Flow Energy Equation.|
|2nd Law of Thermodynamics||Definition of Sink, Source Reservoir of Heat, Heat Engine, Heat Pump & Refrigerator; Thermal Efficiency of Heat Engines & co-efficient of performance of Refrigerators, Kelvin – Planck & Clausius Statements of 2nd Law of Thermodynamics Engineering, Absolute or Thermodynamic Scale of temperature, Clausius Integral, Entropy, Entropy change calculation of ideal gas processes. Carnot Cycle & Carnot Efficiency, PMM-2, definition & its impossibility.|
|Air standard Cycles for IC engines||Otto cycle, plot on P-V, T-S Planes, Thermal Efficiency, Diesel Cycle, Plot on P-V, T-S planes, Thermal efficiency. IC Engine Performance, IC Engine Combustion, IC Engine Cooling & Lubrication.|
|Rankine cycle of steam||Simple Rankine cycle plot on P-V, T-S, h-s planes, Rankine cycle efficiency with & without pump work.
Boilers, Classification, Specification, Fittings & Accessories : Fire Tube & Water Tube Boilers.
Air Compressors & their cycles, Refrigeration cycles, Principle of a Refrigeration Plant, Nozzles & Steam Turbines
|Fluid Mechanics & Machinery|
|Properties & Classification of Fluid||Ideal & real fluids, Newton’s law of viscosity, Newtonian and Non-Newtonian fluids, compressible and incompressible fluids.|
|Fluid Statics||Pressure at a point.|
|Measurement of Fluid Pressure||Manometers, U-tube, Inclined tube.|
|Fluid Kinematics||Stream line, laminar & turbulent flow, external & internal flow, continuity equation.|
|Dynamics of ideal fluids||Bernoulli‟s equation, Total head; Velocity head; Pressure head; Application of Bernoulli’s equation.|
|Measurement of Flow rate Basic Principles||Venturimeter, Pilot tube, Orifice meter.|
|Hydraulic Turbines||Classifications, Principles.|
|Centrifugal Pumps||Classifications, Principles, Performance.|
|Classification of Steels||Mild steel & alloy steel, Heat treatment of steel, Welding – Arc Welding, Gas Welding, Resistance Welding, Special Welding Techniques i.e. TIG, MIG, etc. (Brazing & Soldering), Welding Defects & Testing; NDT, Foundry & Casting – methods, defects, different casting processes, Forging, Extrusion, etc, Metal cutting principles, cutting tools, Basic Principles of machining with (i) Lathe (ii) Milling (iii) Drilling (iv) Shaping (v) Grinding, Machines, tools & manufacturing processes.|
SSC JE Syllabus 2018 PDF
Now all the aspects about SSC JE Mechanical Syllabus 2018 and Exam Scheme of Paper 1 and Paper 2 have discussed above. So candidates must read also official notification and start their exam preparation now. Candidates should be follow this SSC Junior Engineer Mechanical Syllabus Paper I & II carefully and divide your strong and weak area of subjects and prepare hard to crack this hard nut. There are huge syllabus to cover up for the candidates in exam preparation. So we have also provide the topic wise weightage of the marks therefore they can make preference of the exam subjects more scoring. However the candidates should have prepare whole SSC JE Syllabus Mechanical 2018 as published here.
All the candidates are suggested to make their exam preparation plan to following this SSC JE Syllabus 2018 PDF and Exam Pattern discussed above in detailed. We are here updating regularly the latest updates and news regarding the SSC JE Mechanical Syllabus and others.
SSC JE Admit Card 2018 Download :- Click Here
All the aspirants need to keep in touch with SSC JE Preparation Guide team to get more lucrative and important news and updates. Here we are uploading the Practice Mock test papers also as daily.
SSC JE Exam 2018 Important Updates:- Check Here
Click here for more details:– http://ssc.nic.in/
For Latest SSC Jobs Notification Bookmarks This Website (CTRL+D):– www.sscguide.in
“Candidates ask freely their Doubts/Queries regarding examinations as commenting below discuss box. Our Expert Team will assist you shortly. “
“Don’t forget to Share this at Facebook, Twitter, Google+ to help other aspirants.”